Operation Verification

Error Code Verification Test

Verify that there are no current active logged error codes:

1. Access either the Error Log (or CPATouchscreen console Control Processing Assembly. Event Log) and record any current active logged error codes:
   • On P10, P30, P30i and P31 LED consoles, Press & hold down the PAUSE/RESET key for 6 seconds minimum to access the Error Log.
   • On P62, P80, and P82 touchscreen consoles, access Service menu (51765761), select About > CPA Even Log.
2. Resolve any current active logged error code issues.
3. Delete resolved error codes:
   • On P10, P30, P30i and P31 LED consoles, clear the Error Log, see Error Log & CPA Event Log.
     Press and hold the PAUSE/RESET key for 6 seconds minimum to access the Error Log. If there are no logged error codes, the "Stuck Key" message will show. To remove an error code, press/hold down the QUICK START key until the "NO ERRORS" message shows.
   • . On P62, P80, and P82 touchscreen consoles, error codes cannot be deleted from the CPA Event Log)

Console Verification Tests

Verify the LED console or touchscreen console operation.

LED consoles (P10, P30, P30i and P31) only

1. Access the Diagnostic/Test menu (51765761) and run the following tests:
   • KEYPAD TEST: Select KEYPAD TEST and follow prompts to run test.
   • DISPLAY TEST: Select DISPLAY TEST and follow prompts to run test.
2. Exit the Diagnostic Test menu (press the PAUSE/RESET key).

Touchscreen consoles (P62, P80, and P82) only

1. Access the Service menu (51765761) and perform the following console System Tests (Settings > System Settings > System Tests):
   • Touchscreen Calibration: Follow screen prompts to complete test. When the test is completed the console will automatically exit and return to the System Tests menu.
   • Touchscreen Test: Verify that there is a trace created that follows your finger movement across the touchscreen surface. Select Finish to exit. move your finger and verify that a trace follows
   • Backlight Test: Tests the display backlight brightness. Follow prompts to complete test.
   • RGB Test: Touch the screen to cycle through the test colors: Red, Green, Blue, White, & Black. Returns to the System Tests menu when completed.
   • Numeric Backlight Test: Tests the controls numeric display brightness. Returns to the System Tests menu when completed.
   • Numeric Display Test: Tests the controls numeric display. Returns to the System Tests menu.
2. Exit the Diagnostic Test menu. (press Back to exit & return to the banner screen)

Motion Controls Test

Verify the machine operation.

1. Select QUICKSTART to begin a manual workout and operate the treadmill at least 5 minutes. While walking on the unit perform the following tests:
2. Operate the SPEED motion control from minimum to maximum range while verifying the machine operation.
   • Make sure that the console SPEED paddle control operation is smooth and working correctly.
   • Verify that the running belt can reach the maximum speed and then returns to the minimum speed level.
   • Make sure that the running belt speed change is smooth and that there are no unusual noises.
   • Verify that the console SPEED indicators and workout displays are showing correct information.
3. Operate the INCLINE motion controls from minimum to maximum range while verifying the machine operation.
   • Make sure that the console INCLINE paddle controls operation is smooth and working correctly.
   • Verify that the running deck can reach the maximum incline and then return to the minimum incline level.
   • Verify that the lift motor operation is smooth while changing the INCLINE from minimum to maximum levels.
   • Verify that the console INCLINE level indicators and user workout displays are showing correct information.

Running Belt Test

Verify the running belt alignment and tracking.

1. Step off the running belt and operate the treadmill at 12 mph (19 kph) for one minute.
2. Verify the running belt alignment is centered and tracking.

ESTOP Switch Test

Verify the ESTOP emergency switch operation.

1. While walking on the treadmill, press the STOP emergency button and verify that the running belt immediately slows to a stop.
2. While walking on the treadmill, pull the ESTOP lanyard and make sure the running belt immediately slows to a stop.
3. Inspect the condition of the ESTOP lanyard clip, that the spring is in place and that the clip will firmly hold when attached.

Heart Rate Test

Verify the Heart Rate operation.

LED consoles (P10, P30, P30i and P31) only

1. Access the Diagnostic menu (51765761) and run the following tests:
   • HEART RATE TEST: Select HEART RATE TEST and follow prompts run test.

Touchscreen consoles (P62, P80, and P82) only

1. Access the Service menu (51765761) and run the following test.:
   • HEART RATE TEST: Select HEART RATE TEST and follow prompts run test (System Tests (select System Settings > System Tests).

Return to service

1. Switch the power OFF.
2. Make sure that the machine is setting level and stable.
3. On successful completion of these tests, return to service.